EPRO SKP289-3 SKP289 3 SKP2893

Product Description:

The ground conductor of the motor cable should be connected to the drive ground (GRD) terminal directly. Connecting this ground conductor to a cabinet ground point or ground bus bar may cause high frequency current to circulate in the ground system of the enclosure. The motor end of this ground

conductor must be solidly connected to the motor case ground. Shielded or armored cable may be used to guard against radiated emissions from the motor cable. The shield or armor should be connected to the drive ground terminal and the motor ground as outlined in the Grounding section of this Installation

chapter. Common mode chokes are recommended at the drive output to reduce the common mode noise. An RFI filter can be used and in most situations provides an effective reduction of RFI emissions that may be conducted into the main supplylines. If the installation combines a drive with sensitive

devices or circuits,it is recommended that the lowest possible drive PWM frequency be programmed.

Contact Information:

Contact:Miya ( manager)

Email :sales@mooreplc.com
Q Q: 2851195450
Skype: miyazheng520
Mobile:86-18020776792 ( what's app )

Related Product Recommendation:

After starting RSLogix 5000 and either starting a new project or opening an existing project, make sure
that you are OFFLINE with the ControlLogix processor. I/O configuration is only available when offline.
If you have not already defined the contents of your ControlLogix chassis under your project's "I/O

Configuration" folder, you will need to define the ControlNet bridge module at a minimum. Use the right
mouse button to click on the "I/O Configuration" folder, then choose "New Module" from the pop-up menu.From the dialog box that appears, choose the ControlNet bridge of the type (1756-CNB or 1756-

CNBR)and series that you are using. In the next screen, you will need to name the ControlNet bridge and
indicate its position in the ControlLogix chassis (slot 0 is the leftmost).After defining the ControlNet bridge, use the right mouse button to click on the ControlNet bridge under"I/O configuration", then choose "New Module" from the pop-up menu

10 Bolt- Stainless Steel M5 x 30 3 cm long

New Coax Connector RF 90 Degree TRU-3299

PHOENIX CONTACT D-OTTA 25, CONNECTOR TERMINAL, LOT OF 10

AMAT 0010-09195 Robot assembly P5000 CVD tool, 4, 5, 6 inch wafer

NEW DESIGN TECHNOLOGY DT360 ELC-0014-B

24 Vented Aluminum Cap CPTHDAL6061VNT, CPTHAL6061-1724 Size 9 16-18

VAT Valve 14036-PE24, Turbo pump TMH 071P and Turbo Controller TC 750-E74

Chemraz 9024-SC520 2-024 Compound 520 1.114 x 0.070 inch, Oring 78-0128

ENI RF power meter 1006-508 rev 4 MRC CP-10

MKS baratron 124A-11848, 2000 Torr Range, With calibration sheet S224

2 Leybold seal, turbo ISO ring 887061027

2 RF Coax Connector Amphenol S3250

Varian 112415001 Bushing, Feedthru

NEW Perlast 22-294910-00 Oring, white perlast, 3.989 x 0.070

VAT RECTANGULAR GATE, SLIT VALVE MONOVAT 0200X-AE24-1002, VARIAN M2000

Lot of 6 LITTELFUSE V251BA60, METAL OXIDE VARISTOR

Novellus 951479 Cable, motor power

Novellus 951337 Cable, motor power

2 PUV0047-5 power supply HOYA-SCHOTT, UV light source,

3 Banner D12SN6FP Fiber Optic sensor switch

Chemraz 9312-SC520, 2-312, Compound 520, 0.600 x 0.210 inch

Bearing, WFR Roller, MESA 2B-10-241, Used, Lot of 4

Nozzle FLT 80787-50 95Deg@500psi, Lot of two, New

7 RF Low freq silver plated connector AMP, 330830 = 5, 330830-8=2

PHOENIX CONTACT D-OTTA 25, CONNECTOR TERMINAL, LOT OF 10

STEC LF-A40M-A-EVD, TEOS 4g/Min, 3332400050

NEW AMAT 0010-37828 Assy Display Board, HF.RF Generator

NEW AMAT 1400-01325 pressure sensor 0-1MPA 1/8PT 3wire 3m LG, SMC PSE520-T01

NEW AMAT 0090-77009 Assy LVDT ZT-910/900 PM2, Sensotec 060-3590-06, ID 327865

AMAT 0010-12123 Assy PLC Controller 200MM Wald CH. A OR

AMAT 0010-08173 ASSY, SOURCE CONTROL SCA, DPN, 200MM, SSGSE-00002

3 AMAT 0200-09373 West Coast Quartz Cover Ring Quartz Alum 150mm New

AMAT 0010-13389 FORTH POSITION BRACKET ASSEMBLY, BDS6 SH

Astex D13449 Microwave magnetron, D13604 waveguide, C13477 isolator, AMAT HDP

The use of the product:

1.2000+ suppliers with us, we could help you to get any components which is difficult to get.

2.Customer service in 1-4 hours. If there's any question, please contact with our sales.

3.Experienced technichal support team.

Moore Automation is a company specializing in the sales of modules and spare parts for world-renowned brands (DCs systems, robot systems, large servo control systems). The company's products include: distributed control systems (DCS), programmable controllers (PLC), MOTOROLA -MVME industrial modules, industrial control communication converters (Anybus), remote output/input modules (RTU), industrial computers (PC), industrial low-frequency screens (IPC), human-machine interface SCSI (50, 68, 80Pin ) AnyBus(Gateway)o The spare parts we sell provide one-year quality guarantee and have undergone strict testing and certification. Now we have become a global sales enterprise of industrial automation spare parts and components.